Artificial Grass Product Results

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Field Green
• Thatch Zone: Verde

• Grass Zone: 1.875"
• Thatch Zone: 1.625"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. Make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry.
9. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge.

Note: turf should be cut within an 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Field Green
• Thatch Zone: Tweed Turf

• Grass Zone: 2.125"
• Thatch Zone: 1.875"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Field Green
• Thatch Zone: Verde Green

• Grass Zone: 2.0"
• Thatch Zone: 1.75"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Tweed Green
• Thatch Zone: Tweed Green

• Grass Zone: 2"
• Thatch Zone: 1.75"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: EPN Polyethylene
• Thatch Zone: Steam Texturized Nylon

• Grass Zone: Dark Green
• Thatch Zone: Verde

• Grass Zone: 2.0"
• Thatch Zone: 1.75"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk

• Grass Zone: Field Green
• Thatch Zone: Tweed Turf

• Grass Zone: 1.75"
• Thatch Zone: 1.5"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: EPN Polyethylene
• Thatch Zone: Steam Texturized Nylon

• Grass Zone: Dark Green
• Thatch Zone: Verde

• Grass Zone: 1.75"
• Thatch Zone: 1.5"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. Make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry.
9. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge.

Note: turf should be cut within an 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Field Green
• Thatch Zone: Tweed Turf

• Grass Zone: 1.75"
• Thatch Zone: 1.5"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. Make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry.
9. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge.

Note: turf should be cut within an 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Field Green
• Thatch Zone: Verde

• Grass Zone: 2"
• Thatch Zone: 1.75"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. Make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry.
9. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge.

Note: turf should be cut within an 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.

• Grass Zone: Polyethylene
• Thatch Zone: Texturized High Bulk Nylon

• Grass Zone: Field Green
• Thatch Zone: Verde

• Grass Zone: 1.75"
• Thatch Zone: 1.5"

1. Remove sod if necessary.
2. Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
3. Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
4. Level and disperse aggregate with landscape rake.
5. Lightly soak the aggregate.
6. Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

1. Precisely cut the edge against the tufted row.
2. When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
3. Fold back the turf and hold with a temporary weight.
4. Lay 12-18 inch urethane cloth directly under the seam.
5. Secure cloth with a nail at the end of the seams.
6. Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
7. Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. Make sure the fibers do not come in contact with the adhesive.
8. Apply weight on the seams and allow 1hour to dry.
9. When complete, seams may be reinforced with nails.

1. Overlap edges with turf.
2. Secure the position of the turf with nails.
3. As with seaming, fold back turf to the edge exposing the backside.
4. Cut vertical relief cuts to create smaller sections to work with.
5. On the backside, cut the excess turf precisely to the edge.

Note: turf should be cut within an 1/8 inch from the edge.

1. Infill not required for all applications.
2. Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
3. Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
4. After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.