artificial grass never looked more natural
Artificial Grass Products :: SYNAugustine Premium 240
SYNAugustine Premium 240
Price: Call for price
Warranty: 8 year warranty
Total weight: 87 ounces
* Prices reflect product only and do not include installation costs. For installation costs contact your local SYNLawn.
SYNAugustine Premium 240
The premium version of the SYNAugustine collection provides protection from the heat with SYNLawn’s HeatBlock Technology™ and is recommended for landscape applications with kids and pets. The added weight in SYNAugustine Premium 240 artificial grass is preferred in lawns with higher foot traffic and utilization.
- Reduced Surface Temperatures
- Exclusive HeatBlock Technology™ to reduce the impact of the heat causing rays from the sun lowering the surface temperature almost 20%.
- Environment Friendly
- Exclusive EnviroLoc technology with BioCel backing system results in 60%-70% green by weight with greater dimensional stability. Contributes points towards LEED certification.
- Minimal Infill
- Uses only minimal amounts of silica sand for ballast.
- Recommended for
- Residential landscapes, water saturated areas, problem areas and shady areas. Recommended for landscapes with moderate-heavy foot traffic, pet areas for all types of dogs and all types of play areas.
- Yarn type
- Grass Zone:EPN Polyethylene
- Thatch Zone: Steam Texturized Nylon
- Color
- Grass Zone: Meadow Green
- Thatch Zone: Turf Green
- Pile height
- Grass Zone: 1.875"
- Thatch Zone: 1.5"
- Total weight
- 87 ounces
- Warranty
- 8 year warranty year
- Roll width
- 15.00 Feet
- Drain rate
- 30 inches per hour
- Sub-base
- Remove sod if necessary.
- Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
- Install at least 2-4 inches of 1/4"" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
- Level and disperse aggregate with landscape rake.
- Lightly soak the aggregate.
- Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.
Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.
- Seams
- Precisely cut the edge against the tufted row.
- When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
- Fold back the turf and hold with a temporary weight.
- Lay 12-18 inch urethane cloth directly under the seam.
- Secure cloth with a nail at the end of the seams.
- Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
- Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
- Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.
- Edges
- Overlap edges with turf.
- Secure the position of the turf with nails.
- As with seaming, fold back turf to the edge exposing the backside.
- Cut vertical relief cuts to create smaller sections to work with.
- On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.
- Infill
- Infill not required for all applications.
- Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
- Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
- After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.
Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.
Get free samples of SYNLawn artificial grass products
Want to speak to a live person?
Call toll-free: 866-SYNLawn (866) 796-5296
Please call during the hours of 8:00am - 5:00pm M-F Eastern Standard Time
