Artificial Grass Products :: SYNFescue Premium 220

SYNFescue Premium 220

Price: Call for price

Warranty: 8 year warranty

Face weight: 60 ounces

Total weight: 87 ounces

* Prices reflect product only and do not include installation costs. For installation costs contact your local SYNLawn.

SYNFescue Premium 220

Like SYNFescue 120 synthetic grass, SYNFescue Premium 220 employs subtle multi-colored blades to enhance the natural appearance. As a Premium grade class this artificial grass product has a taller blade height and more yarn in the face to boost performance in high traffic areas with minimal infill.

Features
Product Specs
Installation Specs

Environment Friendly: Exclusive EnviroLoc technology with BioCel backing system results in 60%-70% green by weight with greater dimensional stability. Contributes points towards LEED certification.
Minimal Infill: Uses only minimal amounts of silica sand for ballast.
Resiliency: Nylon thatch for resiliency and support combined with polyethylene monofilament long blades for soft feel.
Recommended for: Residential and commercial landscapes, water saturated areas, problem areas and shady areas. Recommended for lawns with moderate to high foot traffic. Maybe used for child play areas, pet areas and pool areas without infill.

Yarn type

Grass Zone: Polyethylene
Thatch Zone: Texturized High Bulk Nylon

Color

Grass Zone: Meadow Green
Thatch Zone: Turf Green

Pile height

Grass Zone: 2.125"
Thatch Zone: 1.875"

Face weight

60 ounces

Total weight

87 ounces

Warranty

8 year warranty year

Roll width

15.00 Feet

Drain rate

30 inches per hour

Sub-base

Remove sod if necessary.
Grade must be at least 3 inches below the border (curbing, edging, patio, etc.).
Install at least 2-4 inches of 1/4" minus compaction aggregate (road base) bringing the grade up to 1 inch below the border.
Level and disperse aggregate with landscape rake.
Lightly soak the aggregate.
Compact aggregate using a vibratory plate compactor. Aggregate may be added to low areas during this process.

Note: Aggregate will stick to the compactor if too wet. At least 80% compaction is ideal.

Seams

Precisely cut the edge against the tufted row.
When seams are in position, place a nail approximately 18 inches from the seam to secure the turf.
Fold back the turf and hold with a temporary weight.
Lay 12-18 inch urethane cloth directly under the seam.
Secure cloth with a nail at the end of the seams.
Pour and spread adhesive on the cloth. (use scrap piece to spread adhesive) Remove the weight from the folds.
Slowly and simultaneously lay both sides of the turf on the adhesive. Avoid overlapping the backing. In addition, make sure the fibers do not come in contact with the adhesive.
Apply weight on the seams and allow 1hour to dry. When complete, seams may be reinforced with nails.

Edges

Overlap edges with turf.
Secure the position of the turf with nails.
As with seaming, fold back turf to the edge exposing the backside.
Cut vertical relief cuts to create smaller sections to work with.
On the backside, cut the excess turf precisely to the edge. Turf should be cut within 1/8 inch from the edge.

Infill

Infill not required for all applications.
Before applying, broom up the fibers of the turf until fibers are standing up. The sand acts as a ballast(weight). A tubular (round) 20 grit sand is recommended.
Evenly distribute a layer of sand by hand or a drop seed spreader (without a spreading wheel) throughout the lawn.
After each layer has been distributed, the infill must be broomed into the base (backing) of the turf fibers.

Note: A quarter inch layer of infill is recommended. Approximately 1-1.5 pounds of infill per square foot.